VW Amarok Mk1 Reverse Light Upgrade Kit

£59.99

Vehicle-specific reverse light upgrade kit for the VW Amarok Mk1, combining a compact LED reversing light with plug-and-play AutoVolt wiring.

In stock

Description

VW Amarok MK1 Reverse Light Kit | Piggyback Loom + Ultra Slim LED

Everything needed for a complete additional reverse light install in one box, with a spare brake light output for later.

This kit pairs our exclusive plug & play VW Amarok MK1 Reverse & Brake Light Piggyback Loom with our Ultra Slim LED Reverse Light, plus the cable and connectors to join the two.

No sourcing parts, no fuse taps, no guesswork. Adding extra rear lighting becomes simple, safe and completely reversible, with no cutting or splicing into factory wiring.

This is an AutoVolt designed solution, developed from the same proven piggyback approach that has worked brilliantly for the Ford Ranger, Toyota Hilux, Nissan Navara, Mitsubishi L200 and Ford Transit Custom. Built to OEM standards for a clean, professional finish and reliable long-term performance.

What’s In The Kit

  • 1 x VW Amarok MK1 Reverse & Brake Light Piggyback Loom – plug & play, three outputs
  • 1 x Ultra Slim LED Reverse / Work Light – 1,400 lumens, R148 approved, 50cm lead attached
  • 1 x 1 metre twin core 1.5mm² thinwall cable – red / black, 21A rated
  • Sealed bullet connector set – for a serviceable disconnect at the light
  • DuraSeal heat-shrinkable, environmentally sealed, nylon-insulated crimp splices – including a spare pair
  • Mounting bracket and screws, rubber installation strip, double sided adhesive pad
  • Installation and connection instructions

Wiring Outputs

⚫ Earth (-) | 🟡 Reverse light (+) | 🔴 Brake light (+)

The supplied LED connects to the reverse output. The brake output stays free for a future additional brake light on a rear bar, rack, canopy or work body.

Cut To Suit | Driver Or Passenger Side

Every vehicle and every mounting position is different, so the extension cable is supplied at a full 1 metre and simply cut to the length that suits your install. Mount on either side.

If you need a longer run, additional cable is available by the metre HERE.

How It Works

The loom takes a safe trigger feed from the factory reverse circuit, so the LED activates automatically the moment the vehicle is put into reverse. No switches, no permanent modifications, and it unplugs completely if you sell the vehicle.

Installation could not be easier: plug the loom in, connect your earth, measure your route, cut the cable to length, and join with the supplied DuraSeal splices.

Ultra Slim LED Specification

  • Output: Approx 1,400 lumens measured
  • Beam reach: 35 metres at 1 lux, flattened vertical spread for low mounting
  • Colour temperature: 5000K neutral white
  • Power: 21W, 12V and 24V compatible
  • Dimensions: 90 x 40 x 15 mm, 90 grams
  • Approvals: R148 reversing light, ECE R10 radio interference
  • Build: Waterproof and corrosion resistant, rated for road salt, UV, moisture and dirt

This light is ECE R148 approved for use as a reversing lamp. UK regulations permit up to two reversing lamps. If the vehicle already has two, one existing reversing lamp must be disabled; otherwise the additional light is for off-road/work-light use only.

Included Cable Specification

2 x 1.5mm² twin core thinwall | 21 / 0.30 stranding | 21A nominal | rated to +120°C | resistant to petrol, diesel, oils, greases and diluted acids. The same automotive grade cable we sell by the metre, not generic hookup wire.

Adding A Second Light?

This kit is supplied with a single 21W light and needs no relay.

If you plan to run more than one additional reverse light or a higher power setup, a relay loom should be used. Ours is available HERE.

In a relay setup, the piggyback loom provides a safe trigger signal only, while the lights draw power directly from the battery through a fused supply. This protects the vehicle circuit, reduces the risk of warning lights, and allows for easy future expansion.

Frequently Asked Questions

Do I need to buy anything else to fit this kit?

No. The kit contains the loom, the light, the cable and the sealed splices needed to join them. You only need basic hand tools and a crimp tool with a heat source for the DuraSeal splices.

Do I need a relay loom with this kit?

No. The kit is supplied with a single 21W light and runs safely from the reverse circuit as supplied. If you plan to run two or more lights, or a higher power setup, a relay loom should be used to draw power directly from the battery through a fused supply.

Can I fit a second reverse light later?

Yes. However, if you are fitting more than one lamp, we strongly recommend using a dedicated reverse light relay loom. This protects the vehicle circuit by using the reverse signal as a trigger only, while powering the lights safely from a fused battery supply. Our purpose made relay loom is available HERE.

What is the brake output for?

The loom also provides a brake light feed, which is left free in this kit. It allows you to add an additional brake light later on accessories such as rear bars, racks, canopies or work bodies without buying another loom.

Will this cause warning lights or CANBUS faults?

When used as intended and within the recommended load limits, this loom does not cause warning lights or CANBUS errors. Issues are most commonly caused by connecting too high a power light without the use of a relay. The light supplied in this kit has been tested and validated on this loom.

Is this loom plug and play?

Yes. The loom is fully plug and play and connects using factory style connectors, with no cutting, splicing or permanent modification required to the vehicle wiring. The only join you make is between the supplied cable and the light.

Can I damage my vehicle by using this kit?

When installed correctly and used within the recommended specifications, this loom is safe and does not damage the vehicle. Problems typically arise when excessive load is added without a relay or when unsuitable lighting is used. Following the guidance above ensures safe operation.

Installation Video

See The LED In Action

New to piggyback looms? Read our guide explaining how they work and how to wire auxiliary lighting safely.

Installation guides and PDFs for this product can be found on our Downloads & Installation Instructions page.

Reviews

There are no reviews yet.

Be the first to review “VW Amarok Mk1 Reverse Light Upgrade Kit”

Your email address will not be published. Required fields are marked *

SKU MK1-AMAROK-REVERSE-LIGHT-KIT Categories , ,
Secret Link
×