Toyota Hilux High Beam Piggyback Wiring Loom (2015-present)

Price range: £17.99 through £52.99

Plug-and-play high-beam piggyback loom for Toyota Hilux 2015+. Take a clean relay trigger for a light bar or spotlights without cutting the factory headlamp wiring.

Description

Toyota Hilux High Beam Piggyback Wiring Loom

Toyota Hilux 2015 Onwards | Plug & Play | High Beam Trigger Loom

LED light is not included. This is the wiring kit needed to connect your own auxiliary lighting.

The AutoVolt® High Beam Piggyback Wiring Loom gives you a safe, simple way to take a true high beam trigger from your Toyota Hilux for auxiliary lighting such as LED light bars, spotlights and driving lights.

It connects inline with your factory headlight wiring, with no cutting, no splicing and no permanent modification to the vehicle. The Hilux has been fitted with several different headlamps and connectors over the years, so the correct loom depends on which type your vehicle has. Please check the guide below before ordering.

Check Your Headlamp Type First

Identifying your headlamp connector is the most important step, as the wrong loom will not fit. Compare the connector on your Hilux to the three types below and to the product photos.

Type 1: 8 Pin Connector (Bi-LED)

SUPPLIED HERE

This is the connector we supply. Our plug and play piggyback loom fits directly inline with the 8 pin Bi-LED headlight connector. This is the loom shown on this page.

Type 1: 24 Pin Connector (Bi-LED)

REQUIRES CAN DEVICE

The 24 pin Bi-LED headlamp cannot take a simple piggyback feed. To pull a high beam trigger from this headlight you will need a CAN bus interface device such as a CANM8 or Laser CANNY. Our piggyback loom is not compatible with the 24 pin connector.

Type 2: 2 Pin Connector (Separate HB3 Bulb)

USE OUR HB3 LOOM

Type 2 headlamps use a separate high beam HB3 bulb on a 2 pin connector. For these we supply our HB3 piggyback loom, which is built for the separate bulb setup rather than the Bi-LED connector.

Important: Relay Required

This loom is a trigger wire only and must be used with a relay wiring loom. It does not supply power to your lights, and running lighting directly from this loom can damage the vehicle’s electrical system.

Both the 8 pin (Type 1) and 2 pin (Type 2) looms are also available bundled with our High Beam Relay Wiring Loom. Add one from the drop down menu, or view full details of the relay loom HERE.

Why Use This Loom?

Modern Hilux lighting systems are sensitive, and tapping into the wiring incorrectly can cause faults or damage. This loom removes that risk by providing a clean, reliable high beam signal for your auxiliary lighting.

Simple Installation

  • Unplug your factory headlight connector and plug the loom inline
  • Route the trigger wire to your relay loom
  • Fully reversible, with no permanent changes

How to Fit the HB3 Piggyback Loom

Watch the short fitting guide below to see the HB3 piggyback loom installed step by step.

Key Features

  • Vehicle specific plug and play fitment
  • Available for Type 1 (8 pin) and Type 2 (2 pin, HB3) headlamps
  • No cutting or splicing required
  • Safe high beam trigger output
  • Optional High Beam Relay Wiring Loom add-on
  • Developed and tested by AutoVolt

Clean, simple and done properly. A safe AutoVolt solution for adding auxiliary lighting to your Toyota Hilux without interfering with the factory wiring.

Additional information

Weight 200 g
Dimensions 25 × 15 × 5 cm
Headlight Type

Type 1 Piggyback Loom Only, Type 1 Piggyback Loom + Relay Wiring Loom, Type 2 – Piggyback Loom Only, Type 2 – Piggyback Loom + Relay Wiring Loom

Reviews

There are no reviews yet.

Be the first to review “Toyota Hilux High Beam Piggyback Wiring Loom (2015-present)”

Your email address will not be published. Required fields are marked *

Secret Link
×