Nissan Navara Reverse Light Upgrade Kit

£59.99

Vehicle-specific Nissan Navara reverse light upgrade kit with a compact LED reversing light and plug-and-play AutoVolt wiring for improved rear visibility.

In stock

Description

Nissan NP300 Reverse Light Kit | Piggyback Loom + Ultra Slim LED

Everything needed for a complete additional reverse light install in one box, with a spare brake light output for later.

This kit pairs our exclusive plug & play Nissan NP300 Reverse & Brake Light Piggyback Loom with our Ultra Slim LED Reverse Light, plus the cable and connectors to join the two.

No sourcing parts, no fuse taps, no guesswork. Designed for seamless integration, the loom connects additional reverse lights and additional 3rd brake lights in a roof bar or canopy without splicing or cutting your existing vehicle wiring.

Our exclusive design protected wiring loom is not available anywhere else. A must-have for off-road enthusiasts and night-time drivers.

What’s In The Kit

  • 1 x Nissan NP300 Reverse & Brake Light Piggyback Loom – plug & play, design protected
  • 1 x Ultra Slim LED Reverse / Work Light – 1,400 lumens, R148 approved, 50cm lead attached
  • 1 x 1 metre twin core 1.5mm² thinwall cable – red / black, 21A rated
  • Sealed bullet connector set – for a serviceable disconnect at the light
  • DuraSeal heat-shrinkable, environmentally sealed, nylon-insulated crimp splices – including a spare pair
  • Mounting bracket and screws, rubber installation strip, double sided adhesive pad
  • Installation and connection instructions

Reverse And Brake Outputs

The supplied LED connects to the reverse output. The brake output stays free for a future 3rd brake light in a roof bar or canopy, with no need to buy another loom.

Cut To Suit | Driver Or Passenger Side

Every vehicle and every mounting position is different, so the extension cable is supplied at a full 1 metre and simply cut to the length that suits your install. Mount on either side.

If you need a longer run, additional cable is available by the metre HERE.

How It Works

The loom takes a safe trigger feed from the factory reverse circuit, so the LED activates automatically the moment the vehicle is put into reverse. No switches, no permanent modifications, and it unplugs completely if you sell the vehicle.

Fitting is four steps: plug in the loom, measure your route, cut the cable to length, and join with the supplied DuraSeal splices.

Ultra Slim LED Specification

  • Output: Approx 1,400 lumens measured
  • Beam reach: 35 metres at 1 lux, flattened vertical spread for low mounting
  • Colour temperature: 5000K neutral white
  • Power: 21W, 12V and 24V compatible
  • Dimensions: 90 x 40 x 15 mm, 90 grams
  • Approvals: R148 reversing light, ECE R10 radio interference
  • Build: Waterproof and corrosion resistant, rated for road salt, UV, moisture and dirt

This light is ECE R148 approved for use as a reversing lamp. UK regulations permit up to two reversing lamps. If the vehicle already has two, one existing reversing lamp must be disabled; otherwise the additional light is for off-road/work-light use only.

Included Cable Specification

2 x 1.5mm² twin core thinwall | 21 / 0.30 stranding | 21A nominal | rated to +120°C | resistant to petrol, diesel, oils, greases and diluted acids. The same automotive grade cable we sell by the metre, not generic hookup wire.

Why Use A Piggyback Loom?

Modern vehicles use sensitive Body Control Modules (BCM). Drawing additional load directly from factory circuits can cause faults or long-term electrical issues. Our loom takes only a signal from the reverse circuit and is designed to work safely with modern vehicle electronics.

Fuse Protection

We always recommend fitting a lower voltage fuse on any lighting system. Our fuse link loom can be added to your basket HERE if required.

Adding A Second Light?

This kit is supplied with a single 21W light and needs no relay.

If you plan to run two or more lights, or add a large light bar, be cautious of the load your BCM can handle. A relay loom should be fitted to take the load. Ours is available HERE.

Installation Video

See The LED In Action

New to piggyback looms? Read our guide explaining how they work and how to wire auxiliary lighting safely.

Installation guides and PDFs for this product can be found on our Downloads & Installation Instructions page.

Reviews

There are no reviews yet.

Be the first to review “Nissan Navara Reverse Light Upgrade Kit”

Your email address will not be published. Required fields are marked *

SKU NAVARA-REVERSE-LIGHT-KIT Categories , ,
Secret Link
×