Description
Mitsubishi L200 Reverse Light Kit | Piggyback Loom + Ultra Slim LED
Everything needed for a complete additional reverse light install in one box, with spare brake and side light outputs for later.
This kit pairs our exclusive plug & play Mitsubishi L200 Rear Lighting Loom with our Ultra Slim LED Reverse Light, plus the cable and connectors to join the two.
No sourcing parts, no fuse taps, no guesswork. Adding extra rear lighting to your L200 becomes simple, safe and completely reversible, with no cutting or splicing into factory wiring.
Like every AutoVolt Solutions product, it is built to OEM standards for a clean, professional finish and reliable long-term performance.
What’s In The Kit
- 1 x Mitsubishi L200 Rear Lighting Piggyback Loom – plug & play, four outputs
- 1 x Ultra Slim LED Reverse / Work Light – 1,400 lumens, R148 approved, 50cm lead attached
- 1 x 1 metre twin core 1.5mm² thinwall cable – red / black, 21A rated
- Sealed bullet connector set – for a serviceable disconnect at the light
- DuraSeal heat-shrinkable, environmentally sealed, nylon-insulated crimp splices – including a spare pair
- Mounting bracket and screws, rubber installation strip, double sided adhesive pad
- Installation and connection instructions
Wiring Outputs
⚫ Earth (-) | 🟡 Reverse light (+) | 🔵 Brake light (+) | ⚪ Side / tail light
The supplied LED connects to the reverse output. The brake and side light outputs stay free for future additions, such as a brake light on a bull bar or side step marker lights run from the side light feed.
Cut To Suit | Driver Or Passenger Side
Every vehicle and every mounting position is different, so the extension cable is supplied at a full 1 metre and simply cut to the length that suits your install. Mount on either side.
If you need a longer run, additional cable is available by the metre HERE.
How It Works
The loom takes a safe trigger feed from the factory reverse circuit, so the LED activates automatically the moment the vehicle is put into reverse. No switches, no permanent modifications, and it unplugs completely if you sell the vehicle.
Installation could not be easier: plug the loom in, connect your earth, measure your route, cut the cable to length, and join with the supplied DuraSeal splices.
Ultra Slim LED Specification
- Output: Approx 1,400 lumens measured
- Beam reach: 35 metres at 1 lux, flattened vertical spread for low mounting
- Colour temperature: 5000K neutral white
- Power: 21W, 12V and 24V compatible
- Dimensions: 90 x 40 x 15 mm, 90 grams
- Approvals: R148 reversing light, ECE R10 radio interference
- Build: Waterproof and corrosion resistant, rated for road salt, UV, moisture and dirt
This light is ECE R148 approved for use as a reversing lamp. UK regulations permit up to two reversing lamps. If the vehicle already has two, one existing reversing lamp must be disabled; otherwise the additional light is for off-road/work-light use only.
Included Cable Specification
2 x 1.5mm² twin core thinwall | 21 / 0.30 stranding | 21A nominal | rated to +120°C | resistant to petrol, diesel, oils, greases and diluted acids. The same automotive grade cable we sell by the metre, not generic hookup wire.
Why Use A Piggyback Loom?
Modern vehicles use sensitive Body Control Modules (BCM). Drawing additional load directly from factory circuits can cause faults or long-term electrical issues. Our loom takes only a signal from the reverse circuit and is designed to work safely with modern vehicle electronics.
Adding A Second Light?
This kit is supplied with a single 21W light and needs no relay.
If you plan to run two or more lights, or a higher power setup, a relay loom should be used. Ours is available HERE.
In a relay setup, the piggyback loom provides a safe trigger signal only, while the lights draw power directly from the battery through a fused supply. This protects the vehicle circuit, reduces the risk of warning lights, and allows for easy future expansion.
Frequently Asked Questions
Do I need to buy anything else to fit this kit?
No. The kit contains the loom, the light, the cable and the sealed splices needed to join them. You only need basic hand tools and a crimp tool with a heat source for the DuraSeal splices.
Do I need a relay loom with this kit?
No. The kit is supplied with a single 21W light and runs safely from the reverse circuit as supplied. If you plan to run two or more lights, or a higher power setup, a relay loom should be used to draw power directly from the battery through a fused supply.
What are the brake and side light outputs for?
Both are left free in this kit. The brake feed lets you add an additional brake light later on accessories such as a bull bar, and the side light feed is ideal for powering side step marker lights. Neither needs another loom.
Will this cause warning lights or CANBUS faults?
When used as intended and within the recommended load limits, this loom does not cause warning lights or CANBUS errors. Issues are most commonly caused by connecting too high a power light without the use of a relay. The light supplied in this kit has been tested and validated on this loom.
Is this loom plug and play?
Yes. The loom is fully plug and play and connects using factory style connectors, with no cutting, splicing or permanent modification required to the vehicle wiring. The only join you make is between the supplied cable and the light.
Can I damage my vehicle by using this kit?
When installed correctly and used within the recommended specifications, this loom is safe and does not damage the vehicle. Problems typically arise when excessive load is added without a relay or when unsuitable lighting is used. Following the guidance above ensures safe operation.
Installation Video
Credit to Tom Wright for this one, it is a great watch.
See The LED In Action
New to piggyback looms? Read our guide explaining how they work and how to wire auxiliary lighting safely.
Installation guides and PDFs for this product can be found on our Downloads & Installation Instructions page.






Reviews
There are no reviews yet.