2024+ Ford Transit Custom Reverse Light Upgrade Kit

£59.99

Reverse light upgrade kit for the 2024+ Ford Transit Custom, combining a compact LED reversing light with plug-and-play AutoVolt wiring for improved rear visibility.

In stock

Description

2024+ Ford Transit Custom Reverse Light Kit | Piggyback Loom + Ultra Slim LED

Everything needed for a complete additional reverse light install in one box. Loom, light, cable and sealed splices included.

⚠ Check Fitment Before Ordering ⚠

Will NOT fit factory LED tail lights. This adapter is for vehicles with standard bulb tail lights only. If your van left the factory with LED rear lights, this kit will not plug in.

Driver side fitment only. The loom must be fitted on the UK offside (driver side) of the van.

This kit pairs our plug & play 2024+ Ford Transit Custom Reverse Light Piggyback Loom with our Ultra Slim LED Reverse Light, plus the cable and connectors to join the two.

No sourcing parts, no fuse taps, no guesswork. Designed for the all new 2024+ models, the loom integrates seamlessly with your factory wiring, so no cutting and no splicing into vehicle wiring is required.

What’s In The Kit

  • 1 x 2024+ Ford Transit Custom Reverse Light Piggyback Loom – plug & play, approx 30cm tail
  • 1 x Ultra Slim LED Reverse / Work Light – 1,400 lumens, R148 approved, 50cm lead attached
  • 1 x 1 metre twin core 1.5mm² thinwall cable – red / black, 21A rated
  • Sealed bullet connector set – for a serviceable disconnect at the light
  • DuraSeal heat-shrinkable, environmentally sealed, nylon-insulated crimp splices – including a spare pair
  • Mounting bracket and screws, rubber installation strip, double sided adhesive pad
  • Installation and connection instructions

Cut To Suit Your Install

Every mounting position is different, so the extension cable is supplied at a full 1 metre and simply cut to the length that suits your install.

Total available reach is approximately 1.8 metres from the loom tap point (30cm loom tail + 1m cable + 50cm light lead).

As the loom fits on the driver side, this reach suits a driver side or centre mounted light. If you are mounting on the passenger side or running a longer route, add extra cable by the metre HERE.

How It Works

The loom takes a safe trigger feed from the factory reverse circuit, so the LED activates automatically the moment the van is put into reverse. No switches, no permanent modifications, and it unplugs completely if you sell the vehicle.

Fitting is four steps: plug in the loom, measure your route, cut the cable to length, and join with the supplied DuraSeal splices. Ideal for improving visibility when reversing, loading, towing or manoeuvring at night.

Ultra Slim LED Specification

  • Output: Approx 1,400 lumens measured
  • Beam reach: 35 metres at 1 lux, flattened vertical spread for low mounting
  • Colour temperature: 5000K neutral white
  • Power: 21W, 12V and 24V compatible
  • Dimensions: 90 x 40 x 15 mm, 90 grams
  • Approvals: R148 reversing light, ECE R10 radio interference
  • Build: Waterproof and corrosion resistant, rated for road salt, UV, moisture and dirt

This light is ECE R148 approved for use as a reversing lamp. UK regulations permit up to two reversing lamps. If the vehicle already has two, one existing reversing lamp must be disabled; otherwise the additional light is for off-road/work-light use only.

Included Cable Specification

2 x 1.5mm² twin core thinwall | 21 / 0.30 stranding | 21A nominal | rated to +120°C | resistant to petrol, diesel, oils, greases and diluted acids. The same automotive grade cable we sell by the metre, not generic hookup wire.

Why Use A Piggyback Loom?

Modern vehicles use sensitive Body Control Modules (BCM). Drawing additional load directly from factory circuits can cause faults or long-term electrical issues. Our loom takes only a signal from the reverse circuit and is designed to work safely with modern vehicle electronics.

Adding A Second Light?

This kit is supplied with a single 21W light and needs no relay. If you plan to run two or more lights, we strongly recommend a relay loom to protect the vehicle’s BCM. Ours plugs directly into this piggyback loom and is available HERE.

See The LED In Action

New to piggyback looms? Read our guide explaining how they work and how to wire auxiliary lighting safely.

Installation guides and PDFs for this product can be found on our Downloads & Installation Instructions page.

Reviews

There are no reviews yet.

Be the first to review “2024+ Ford Transit Custom Reverse Light Upgrade Kit”

Your email address will not be published. Required fields are marked *

SKU NEW-TRANSIT-CUSTOM-REVERSE-KIT Categories , ,
Secret Link
×