12V Automatic LED Dimmer with Trigger Wire | AutoVolt Trigger-Dim

£39.99

Automatically dim your 12V LEDs when a positive 12V trigger wire goes live. Full brightness normally, then dimmed to the level you set on the dial. Returns to full when the trigger is removed.

Cased and pre-wired with five colour-coded tails and 4mm bullet connectors, mating bullets included. Manual mode. 2A maximum (24W at 12V). Lowest setting may appear off, but is not a safety disconnection.

In stock

Description

At a glance

  • What it does: your LEDs run at full brightness, then dim to the level you set when a 12V trigger wire goes live, and go back to full when it goes dead
  • You set the level: turn the dial for anything from slightly dimmed right down to dark
  • Trigger: a switched positive 12V wire, such as sidelights, headlights, ignition, reverse or a switch
  • For: standard 12V LED strips and modules, up to 2A (24W)
  • Ready to connect: cased and pre-wired with five colour-coded tails fitted with 4mm bullet connectors, plus the mating bullets to crimp onto your own wires
  • AutoVolt design: the same dimmer we fit in our LED grille light kits, now sold on its own. Designed and built in Northern Ireland

How it works

  • No trigger: lights on at full brightness.
  • 12V on the blue wire: lights drop to the level set on the dial.
  • Trigger removed: lights go straight back to full.
  • Manual mode: flick the mode switch and use it as a simple dimmer with no trigger wire at all.

Where it can be used

  • Grille and accent lights: full in daylight, dimmed or dark when the sidelights or headlights come on.
  • Switch panels, gauges and footwell LEDs: easy to see by day, soft on the eyes at night.
  • Kit cars, classics and custom builds: make a small LED light dim or go dark when another circuit comes on, without building relay logic.
  • Indicator trigger: accent strip dims or blanks on each flash so the indicator stands out.
  • Reverse trigger: rear accent or underglow LEDs dim in reverse so they do not glare out the reversing camera.
  • Vans and campers: small interior strips full when parked, dimmed when the ignition is on.
  • Show vehicles: feed the trigger from a flasher or strobe controller and the lights pulse between full and your set level. Off-road and show use.
  • Away from vehicles: home cinema LED strips that dim when the projector starts, display and model lighting.

Examples are subject to the connected lighting, trigger wiring and applicable installation rules. This module is not intended for safety-critical lighting circuits.

More information

Wiring
Red Ignition live (+). Connect to a fused 12V ignition feed. Fuse and fuse holder are not supplied, use a 3A fuse. Use an ignition feed, not a permanent live, to avoid standby draw.
Black Earth (-). Connect to chassis ground.
Green Light live (+). Connect to the positive of your LED light.
White Light earth (-). Connect to the negative of your LED light.
Blue Dimmer signal (+). The 12V wire you want to trigger dimming, for example a sidelight feed. It is a plain 12V input, not a CAN bus connection. Check the signal first, as some vehicle lighting outputs are PWM-controlled.
Specifications
Supply 10 to 15V DC. Not for 24V systems.
Maximum load 2A maximum (24W at 12V)
Trigger Positive 12V. The trigger input does not feed power back into the trigger wire.
Switching Positive side PWM. The light’s negative can go to chassis ground as normal.
Controls Rotary knob for brightness, mode switch for Auto or Manual
Connections Five colour-coded wire tails in braided sleeving, each with a 4mm bullet connector. Mating bullet connectors included.
Housing Compact black case with wiring key on the label. Not waterproof.
Good to know before you buy
  • Which lights it suits: compatible constant-voltage 12V LED strips and LED modules. Lights with their own built-in driver, such as many light bars and pods, may flicker or not dim.
  • It controls brightness, not guaranteed isolation: the LEDs run at full output by default and change to the preset PWM level when triggered. The lowest setting may appear off, but complete electrical disconnection is not guaranteed. To do the opposite, dim normally and full on a signal, add a standard changeover relay on the trigger wire.
  • Negative-switched triggers: the trigger needs a positive 12V signal. A ground-switched wire needs a relay to convert it.
  • Keep it dry: the case is not waterproof. Mount it inside the vehicle or somewhere dry, away from engine heat.
  • Road use: changing how exterior lights behave on a road vehicle is the fitter’s responsibility. Check your lighting regulations.
Questions
  • Can I set how dim the lights go? Yes. The dial adjusts the triggered PWM brightness. Some LEDs may appear completely dark at the lowest setting, but this is not an electrical isolation switch.
  • Does it need a BCM? No. Use a suitable positive 12V trigger source with a shared ground reference. Confirm compatibility before connection.
  • Will it work on a campervan or a home cinema strip? Potentially, if the supply is within 10 to 15V, the positive trigger is suitable, and the LED load is compatible and within 2A.
  • Is it the same dimmer as in your grille light kits? Yes, the same unit, sold on its own.

Reviews

There are no reviews yet.

Be the first to review “12V Automatic LED Dimmer with Trigger Wire | AutoVolt Trigger-Dim”

Your email address will not be published. Required fields are marked *

SKU AV-TRIGGER-DIM Category
Secret Link
×