Description
Next Gen Ford Ranger (2023-Present) Reverse Light Kit | Piggyback Loom + Ultra Slim LED
Everything needed for a complete additional reverse light install in one box. Available for both Standard and BLIS® tail lights.
This kit pairs our plug & play Next Gen Ford Ranger Reverse Light Piggyback Loom with our Ultra Slim LED Reverse Light, plus the cable and connectors to join the two.
No sourcing parts, no fuse taps, no guesswork. The loom plugs straight into the factory harness for a clean, reversible, OEM-style installation with no cutting and no splicing into vehicle wiring. Suitable for 2023-Present models.
What’s In The Kit
- 1 x Next Gen Ford Ranger Reverse Light Piggyback Loom – Standard or BLIS®, plug & play, approx 30cm tail
- 1 x Ultra Slim LED Reverse / Work Light – 1,400 lumens, R148 approved, 50cm lead attached
- 1 x 1 metre twin core 1.5mm² thinwall cable – red / black, 21A rated
- Sealed bullet connector set – for a serviceable disconnect at the light
- DuraSeal heat-shrinkable, environmentally sealed, nylon-insulated crimp splices – including a spare pair
- Mounting bracket and screws, rubber installation strip, double sided adhesive pad
- Installation and connection instructions
Cut To Suit | Driver Or Passenger Side
Every vehicle and every mounting position is different, so the extension cable is supplied at a full 1 metre and simply cut to the length that suits your install. Mount on either side.
Total available reach is approximately 1.8 metres from the loom tap point (30cm loom tail + 1m cable + 50cm light lead).
How It Works
The loom takes a safe trigger feed from the factory reverse circuit, so the LED activates automatically the moment the vehicle is put into reverse. No switches, no permanent modifications, and it unplugs completely if you sell the vehicle.
Fitting is four steps: plug in the loom, measure your route, cut the cable to length, and join with the supplied DuraSeal splices.
The AutoVolt BLIS® Loom | Found Nowhere Else
Tail lights fitted with BLIS® use a completely different connector and wiring layout to standard units, because the blind spot sensors and warning system are built into the rear light assembly. A standard piggyback loom simply will not plug in.
Our BLIS® loom is designed in-house to plug directly into the factory BLIS® tail light connector and take a clean signal feed from the reverse circuit without interfering with the blind spot sensors or warning system. Your BLIS® functionality stays fully intact, and you gain a safe, automatic trigger for additional reverse or rear work lights.
This is the sole design of AutoVolt and is not available anywhere else. If you run BLIS® tail lights, this is the only true plug & play kit on the market.
Ultra Slim LED Specification
- Output: Approx 1,400 lumens measured
- Beam reach: 35 metres at 1 lux, flattened vertical spread for low mounting
- Colour temperature: 5000K neutral white
- Power: 21W, 12V and 24V compatible
- Dimensions: 90 x 40 x 15 mm, 90 grams
- Approvals: R148 reversing light, ECE R10 radio interference
- Build: Waterproof and corrosion resistant, rated for road salt, UV, moisture and dirt
This light is ECE R148 approved for use as a reversing lamp. UK regulations permit up to two reversing lamps. If the vehicle already has two, one existing reversing lamp must be disabled; otherwise the additional light is for off-road/work-light use only.
Included Cable Specification
2 x 1.5mm² twin core thinwall | 21 / 0.30 stranding | 21A nominal | rated to +120°C | resistant to petrol, diesel, oils, greases and diluted acids. The same automotive grade cable we sell by the metre, not generic hookup wire.
Why Use A Piggyback Loom?
Modern vehicles use sensitive Body Control Modules (BCM). Drawing additional load directly from factory circuits can cause faults or long-term electrical issues. Our loom takes only a signal from the reverse circuit and is designed to work safely with modern vehicle electronics.
Adding A Second Light?
This kit is supplied with a single 21W light and needs no relay. If you plan to run two or more lights, we strongly recommend a relay loom to protect the vehicle’s BCM. Ours plugs directly into this piggyback loom and is available HERE. Additional cable is available by the metre HERE.
See The LED In Action
New to piggyback looms? Read our guide explaining how they work and how to wire auxiliary lighting safely.
Installation guides and PDFs for this product can be found on our Downloads & Installation Instructions page.






Reviews
There are no reviews yet.